1.1. TOYOTA, LEXUS, SUBARU (2007-2024) (РЕЖИМ 1)

1.2. BMW, KIA,HYUNDAI, TESLA, NISSAN, PORSCHE, TANK, FORD, VOLKSWAGEN,

LANDROVER,LANDWIND,LINCOLN,LOTUS,MASERATI,MAYBACH,MCLAREN,

MINI, HONDA, DODGE, MAZDA, OPEL, PEGEOUT, SKODA, SMART,

VOLVO,ALPINA , BAIC , BAW ,BENTLEY, BUGATTI, BUICK , CADILLAC,

CHANGFENG, CHEVROLET, CHRYSLER, CITROEN, CUPRA, DACIA, DAIMLER,

EXEED+,FAW,FERRARI,FIAT,FISKER,

GENESIS,GEELY,GMC,INFINITY,INVICTA,JAC,JEEP,KOENIGSEGG,LAMBORGHI

NI,PAGANI,PROTON,QOROS,RENAULT,ROLLS-ROYCE SEAT,SUZUKI.

(2005- 2024) (РЕЖИМ 2)

1.3 AUDI, MERCEDES-BENZ, JEEP (2007-2024) (РЕЖИМ 3)

1.4 THE WHOLE RANGE OF CHINESE TYPE CARS ZEEKR, CHANGAN, EXEED,

DFM, CHERY, FAW, GAC, GEELY, GREAT WALL POER, HAVAL, JAC, LI, NIO,

AVATR, HUAWEI, JAECOO, OMODA, JETOUR (2016-2024) (РЕЖИМ 4)

2.1 THE DEVICE CONSISTS OF TWO BLOCKS, THE BLOCK А (GOES TO THE CAR), UNIT B (GOES TO THE KEY), UNIT B CHARGER, ADDITIONAL ANTENNA (NOT INCLUDED WITH THE DEVICE), UNIT A CHARGER.

 









CONNECTOR 1: CHARGER CONNECTOR.
(ATTENTION THE CHARGER MUST NOT EXCEED 5 VOLTS, 1A)

CONNECTOR 2: PROGRAMMING CONNECTOR. (USED FOR FREE UPDATES)

2

 
BUTTON 1: PIN CODE ENTRY BUTTON, MODE SELECTION.

 


РCONNECTOR 1: PROGRAMMING CONNECTOR. (USED FOR FREE
UPDATES) ( DO NOT USE )
BUTTON 1: THE SWITCH BUTTON FOR THE INTERNAL ANTENNA AND ADDITIONAL ANTENNAS
LED 1: POWER LED AND OPERATION MODE ACTIVATION INDICATOR
LED 2: THE LED INDICATOR FOR ON-OFF MODE IS OPTIONAL.ANTENNAS
CONNECTOR 2: CHARGER CONNECTOR. (ATTENTION!!! THE CHARGER
THE DEVICE MUST BE USED WITH A 12V 2A KIT)
CONNECTOR 3: CONNECTOR FOR AN ADDITIONAL ANTENNA
THE SWITCH: ON-OFF UNIT B.

3. PIN CODE ENTRY
3.1 ATTENTION PIN CODE ENTRY IS LIMITED (15 TIMES) IF YOU DO NOT ENTER
   IF CORRECT, THE DEVICE WILL LOCK (YOU CAN UNLOCK IT
   REMOTELY) (THIS IS DONE FOR YOUR SAFETY)
3.2 THE PIN CODE IS ENTERED ONLY ON BLOCK A
3.3 THE PIN CODE CONSISTS OF "XX" DIGITS 1-9 (DETERMINED BY PRESSING,
   THAT IS, THEY PRESSED THE BUTTON 1 TIME, WHICH MEANS THERE WILL BE A NUMBER 1, THEY PRESSED
   4 TIMES - THE NUMBER WILL BE 4 AND SO ON 2 TIMES) AFTER EACH EPISODE
   AFTER PRESSING, THERE WILL BE A CONFIRMATION INDICATION OF THE INPUT.
   INPUT EXAMPLE: THE PIN CODE OF THE SYSTEM IS 35
(PRESSING, PRESSING, PRESSING (WAITING)
(WE SEE THE LED BLINKING CONFIRMING THE INPUT) (1 TIME)
TAP, TAP, TAP, TAP, TAP.(WAITING)
(IF EVERYTHING IS DONE CORRECTLY, THE SYSTEM WILL BLINK AT YOU
   TURN ON THE LEDS 4 TIMES)

3.4 MODE SELECTION: THE MODES ARE LISTED ON PAGE No1 SELECTION
THE MODE IS PERFORMED BY PRESSING 1-4 TIMES (EXAMPLE: YOU NEED A SECOND ONE
MODE (MULTI–BRAND+) - PRESSING, PRESSING (WAITING) )
IF EVERYTHING IS DONE CORRECTLY, THE "LED 1" ON BLOCK A WILL BLINK
THE NUMBER OF BLINKS DEPENDS ON THE SELECTED MODE 3=3.2=2.
ALSO, "LED 1" WILL BLINK ON UNIT B. THE DEVICE IS READY FOR OPERATION FOR NOW
DO NOT TURN OFF UNIT A.
4. Working in practice:

 

     4.1. The best signal reception location for BLOCK A is marked in red.
    1-2-4 mode. Do not bring BLOCK A too close to the handle of the T.S. (15-20 cm)
   
   

 

   4.2. The best signal reception location for block A in mode 3 is marked in bright red.

     

 

     4.3. This figure shows the best place to launch in  red.
     That is, in all modes, unwanted signal reception is marked in blue.
     
     4.4. The control unit should preferably be located exactly parallel to the key on both     the internal antenna and the additional one.


 

     

     


4.5. The additional antenna should preferably be square in shape.
70x70x70x70 with these parameters, the longest distance to the key is achieved.

5. The charger:
5.1. To charge unit A, "connector 1" (MICRO-USB) is used
. You can charge with 5 Volt 1A charging, and you can also charge with car
charging with the same parameters. Charge indication on the front of the
device (Blue LED -Charging) (Yellow LED-Charged)
5.2. To charge unit B, the "Connector 2" adapter supplied
is used, the charge indicator is located on the adapter itself (Red
LED -Charging) (green LED-Charged)
6. System characteristics:
6.1. Unit A weight: 220 grams, total charging time (2 hours).
The time of the possibility of permanent work:3 hours.(Enough for 4 days of operation)
There is protection against overcharging and overheating of the system. Also protection from
moisture ingress.
6.2. Unit B weight: 1.1 kg, total charging time (2 hours) There is protection against
overcharging and overheating of the system.
Permanent work time: 12 hours. (Enough for 7 days
of work)
6.3. The material of the devices is reliable and practical ABS Plastic. The system is not
afraid of falls, shaking, etc.
7. Warnings:
7.1. DO NOT LEAVE THE SYSTEM IN THE CAR IN SUBZERO TEMPERATURES.
7.2. DO NOT LEAVE ON CHARGE FOR MORE THAN 12+ HOURS.
7.3. DO NOT KEEP IT SWITCHED ON UNNECESSARILY.
7.4. DO NOT TURN ON THE MODE WHEN BLOCKS A AND B ARE CLOSER THAN 2 METERS.
7.5. DO NOT EXPOSE TO MOISTURE.
7.6 STORE IN A CHARGED STATE.